X 360 Connectivity Kit V3 and LT Switch Combo - CK3 & LT Switch Bundle (8/9)
Product Description
This is a must have for your Liteon (Lite-on) DVD drive.
This tool combines a Connectivity Kit V3 plus a solder kit.
This is the version 3 of the adapter. The version 3 features the following improvements:
* Improved PCB design and layout
* Added support for debug mode (on some DVD-ROMs)
* Added two LEDs to indicate the status of "Eject" button
* Added two LEDs to indicate the status of "Debug" button
* Added power on/off switch
* Included a DVD power cable
* Using a higher VA rating low dropout postive regulator to convert 5V DC to 3.3V DC
* Include all the required components for your
* Works with any PCs.
You also need a PCI to SATA controller card and case opening tool.
This board has an eject switch for the driver and 2 LED indicators to tell you the board is functioning.
This board also has an Debug switch for drivers supporting debug mode.
This board also has a power on/off switch.
Warnings
In order to connect the DVD to your PC, you have to open the case, which invalidates your warranty. If you want to keep you warranty, do not try this.
We are NOT responsible for any misreading or damage done to your box / computer in any way.
Warning
We strongly encourage you to use multimeter to check the trace after rejoin it using silver glue (when it is dried). Fail to do that, you may damage your DVD drive.
If you are not too afraid of soldering, you can also solder the cuts, however, you still need to use multimeter to check the joint, to make sure there is no short circuit.
You are responsible for any damage you cause to your device. We are not liable for any damages you cause to your device.
This product is a simple power converter, no custom firmware or any code. The only IC on this board is a power regulator, other components are just resistors, caps and switches etc.
This tool combines a Connectivity Kit V3 plus a solder kit.
This is the version 3 of the adapter. The version 3 features the following improvements:
* Improved PCB design and layout
* Added support for debug mode (on some DVD-ROMs)
* Added two LEDs to indicate the status of "Eject" button
* Added two LEDs to indicate the status of "Debug" button
* Added power on/off switch
* Included a DVD power cable
* Using a higher VA rating low dropout postive regulator to convert 5V DC to 3.3V DC
* Include all the required components for your
* Works with any PCs.
You also need a PCI to SATA controller card and case opening tool.
This board has an eject switch for the driver and 2 LED indicators to tell you the board is functioning.
This board also has an Debug switch for drivers supporting debug mode.
This board also has a power on/off switch.
Warnings
In order to connect the DVD to your PC, you have to open the case, which invalidates your warranty. If you want to keep you warranty, do not try this.
We are NOT responsible for any misreading or damage done to your box / computer in any way.
Warning
We strongly encourage you to use multimeter to check the trace after rejoin it using silver glue (when it is dried). Fail to do that, you may damage your DVD drive.
If you are not too afraid of soldering, you can also solder the cuts, however, you still need to use multimeter to check the joint, to make sure there is no short circuit.
You are responsible for any damage you cause to your device. We are not liable for any damages you cause to your device.
This product is a simple power converter, no custom firmware or any code. The only IC on this board is a power regulator, other components are just resistors, caps and switches etc.
Additional Information
| Manufacturer | Unknown |
|---|---|
| Warranty | 1 year limited replacement warranty |
| Interface | No |
You may also be interested in the following product(s)
Connectivity Kit V3 and Ultimate Liteon USB Solderless Extractor Combo (7/8/9)
$37.99
|
Related Products
Check items to add to the cart or select all
My Cart
You have no items in your shopping cart.
Product QR Code
Compare Products
You have no items to compare.
